[China glass net] installation method of glass door 1. Construction process positioning, top line of the mounting frame, metal groove, metal bottom, vertical door frame, glass installation, glass door, upper and lower door, door leaf, positioning, installation, installation, glass door handle Construction methods and technical measures (1) Positioning and paying off: The glass door combined with fixed glass and movable glass door leaf is used for uniform positioning. According to the requirements of the design and construction drawings, the positioning line of the glass door is released, and the position of the door frame is determined, and the ground level and the top level of the door frame and the height of the middle frame are accurately measured.
(2) Limiting groove at the top of the mounting frame: The width of the limiting slot should be greater than the thickness of the glass 2-4mm and the groove depth is 10-20mm. When installing, firstly pull out the two metal decorative board edges from the drawn line, and then press the side line to install the limit slot at the top of the door frame. The groove depth in the notch is adjusted by a gluing pad. In addition to the wood lining, the limit groove is made of 1.5mm steel plate pressing, steel plate welding and aluminum metal profiles and other lining outsourcing stainless steel.
(3) Install the wooden bottom of the metal veneer: first fix the square wood on the ground, and then stick the metal veneer to the wood with the multifunctional glue. The square wood can be directly nailed to the pre-buried wooden brick, or pass The method of expansion bolt connection is fixed. If aluminum alloy square tube is used, it can be fixed on the frame column with aluminum angle or fixed on the wooden brick buried in the ground with wood screws.
(4) Install the vertical door frame: connect the center line of the bullet to the door frame, and then use plywood to determine the shape and position of the door frame. Later, the metal decorative surface is outsourced. When facing the veneer, place the face-to-head seams on the sides of the door on the mounting glass. The seam location must be accurate and vertical.
(6) Fixing glass: Two small square wooden strips on the bottom and side of the wooden base are placed on the middle door, the square wooden strip is about 4mm away from the glass plate surface, and then the multi-purpose glue is applied on the square wooden strip. , the decorative metal is stuck on the square bar.
(7) Injection glass seal: In the gap between the top limit groove and the bottom bracket, and the gap between the thick glass and the frame column, the glass seal is injected, and when the glue is injected, the glue is required to be injected. The beginning of the gap begins, and the gap is evenly poured, so that the glass glue forms a uniform straight line outside the slit, scraping off the excess glass glue with a plastic sheet, and rubbing the glue with a cloth.
(8) Docking between glass: When the glass door fixing part needs to be spliced ​​by the size of the large size, the seam should have a width of 2-3 mm, and the edge of the glass plate should be chamfered. After the glass is fixed, the glass glue is injected into the butt gap. After filling, use a plastic sheet to flatten the rubber on both sides of the glass plate to make the gap form a clean and uniform straight line. Clean the rubber trace with a clean cloth on the glass surface.
(9) Activity glass door installation: Before the door leaf is installed, the grounding spring and the positioning pin on the top surface of the door frame should be positioned and installed. The two must be coaxial. When installing, check the vertical line to ensure the spring shaft and the positioning pin. The center line is on the same line.
(10) Install the glass door leaf upper and lower door clamps: Install the upper and lower metal door clips on the upper and lower ends of the glass door and measure the height of the door. If the upper and lower edges of the door leaf are more than the specified value from the horizontal frame of the door and the ground, that is, the height of the door leaf is not enough, the wooden plywood strip can be placed at the bottom of the glass in the lower lower door clamp.
(11) Fixed glass door upper and lower door clamps: After setting the height of the door leaf, insert the small wooden strips at the same time in the gap between the thick glass and the metal upper and lower door clamps, tap the solid, then in the small wooden strip, thick glass, door clamp Inject a glass glue into the gap between them.
(12) Positioning and installation of the door leaf: firstly adjust the positioning pin on the beam of the door frame with its own adjusting screw to the plane of the beam 2mm; then erect the glass door leaf to align the hole of the rotating pin connector in the lower door clamp of the door leaf The spring rotates the pin shaft and rotates the door leaf to insert the hole into the pin shaft; initially, the door leaf is rotated 900 so as to be at right angles to the door frame beam, and the hole of the rotating connecting member in the door leaf door clamp is aligned with the position on the door frame beam. Pin, adjust the adjusting screw of the positioning pin, and insert the positioning pin into the hole about 15mm.
(13) Install the glass door handle; the handle hole of the all-glass door leaf is generally processed when cutting the glass. The handle connection part should not be too tight when inserted into the hole, and should be slightly loose; if the insertion is too loose, the flexible part can be wrapped in the insertion part. Apply a little glass glue to the part of the handle that is inserted into the glass before installation. When the handle is assembled, the root is tightly attached to the glass and then the fixing screw is pressed to ensure that the handle is not loose.
Digital Fabric,Digital Printing Fabric,Digital Printing On Fabric,Digital Print Fabric Wholesale
SHAOXING YINFENG IMPORT AND EXPROT CO.,LTD , https://www.shaoxingyinfeng.com